- Service in Österreich
- Unser Service Netzwerk
- Customer Support
- Info Service
- Service Locations
|Simplify Your Envelope Tracking System||18.11.2013|
The R&S®SMW200A vector signal generator combined with the R&S®FSW signal and spectrum analyzer offers fast and simple power amplifier testing including envelope tracking, effectively replacing complex test setups.
|Simplifying mixer measurements with the R&S®ZNB||01.10.2013|
The R&S®ZNB vector network analyzer simplifies instrument configuration and calibration using the mixer measurement wizard and SMARTerCal.
|Fast and accurate passive intermodulation (PIM) measurements||27.09.2013|
Unique automatic level controlled (ALC) based test setup using the R&S®ZVA vector network analyzer and R&S®BBA150 broadband amplifiers provides highly accurate and reproducible results in minimum test time.
|R&S®RTO Analyze EMI problems with the R&S®RTO||18.09.2013|
The R&S®RTO digital oscilloscope is a valuable tool for analyzing EMI problems in electronic designs. High input sensitivity, high dynamic range and a powerful FFT implementation are key features for capturing and analyzing unwanted emissions.
|Test your eCall In-Vehicle System Modules Reliably||10.09.2013|
The R&S®CMW500 and R&S®SMBV100A are the ideal team for testing your eCall system’s cellular modem and GNSS receiver in a lab environment.
|Testing airborne radios to the limits||09.08.2013|
Replace extensive field tests on fast frequency hopping radios by simulating real-world radio link conditions in the lab
|Analyze your radar signals with wideband power sensors||06.08.2013|
High sampling rate and automatic pulse analysis make the R&S®NRP-Z8x wideband power sensors ideal for time-domain analysis of radar pulses.
|Tamper protection for monitoring networks in banks||15.07.2013|
The R&S®SITLine ETH's military-grade cryptography secures monitoring network data.
|Simplified analysis of frequency agile radars||04.07.2013|
The R&S®FSW signal and spectrum analyzer with the R&S®FSW-K160R realtime option and the R&S®FSW-K6 pulse measurement option is ideal for testing modern radars.
|WLAN IEEE 802.11ac – Wideband Signal Testing||27.06.2013|
Offering bandwidths up to 160 MHz, the signal generators and analyzers from Rohde & Schwarz are ideal for testing IEEE 802.11ac signals
|Analog and digital audio measurements with the R&S®CMW||20.06.2013|
The R&S®CMW-B400B audio board offers the flexibility to measure and quantify audio applications with the R&S®CMW270/280/500 radio communication testers.
|R&S®VCS-4G for simulator and training systems||18.06.2013|
VoIP for air traffic control
|R&S®VCS-4G for emergency voice communications systems||18.06.2013|
VoIP for air traffic control
|Measuring the linearity of cable amplifiers||18.06.2013|
To measure linearity, a single R&S®CLG cable load generator generates the entire full digital channel load of a cable TV network. When the R&S®CLG is used together with the R&S®ETL TV analyzer, the resulting bit error ratio (BER) or carrier-tointerference noise ratio (CINR) can be directly determined in line with IEC 60728-3-1.
|R&S®VCS-4G for geographically distributed voice communications systems||17.06.2013|
VoIP for air traffic control
|Testing hopping radios with confidence||04.06.2013|
The R&S®FSW signal and spectrum analyzer with the R&S®FSW-K160R realtime option enables wideband signal analysis and high probability of intercept.
|R&S®ZVA-K9 Measure group delay without LO access||17.05.2013|
The R&S®ZVA vector network analyzer with the R&S®ZVA-K9 option enables absolute group delay measurements on devices with embedded LO without the need for a calibration mixer
|R&S®ESMD Increasing timestamp accuracy in TDOA applications||30.04.2013|
Using the internal R&S®ESMD-IGT GPS module and external GPS antenna in the R&S®ESMD wideband monitoring receiver
|Troubleshooting utilizing SNMP - For solving intermittent faults in broadcast networks||22.04.2013|
For solving intermittent faults in broadcast networks
|R&S®BCMux, R&S®SFU Interoperability tests of DVB-T2 receivers||18.04.2013|
Correct and time-saving parameter configuration thanks to predefined DVB-T2 test configurations in the R&S®SFU broadcast test system
|Efficiently testing car antennas for broadcast signals||07.03.2013|
Two R&S®ETL TV analyzers or two R&S®ETC compact TV analyzers are used to measure the receive level of a car antenna against that of a reference antenna. The R&S®Broadcast Drive Test Software exports measured data for display in Google Earth.
|Optimize the quality of experience of mobile devices||25.02.2013|
First integrated data end-to-end solution with IP analysis and protocol statistics allows detailed analysis of apps.
|R&S®CMWrun Sequencer software tool||19.02.2013|
Ready-to-use solution for configuring RF and data application test sequences by remote control – for all standards supported by the R&S®CMW family.
|R&S®RFID 18000-6C Analysis Software||18.01.2013|
|Hybrid Broadcast Broadband Television (HbbTV)||28.12.2012|
Signaling checks, DSMCC object carousel analysis and fault localization all in one instrument: R&S®DVMS, R&S®DVM or R&S®ETL
|R&S®VCS-4G in mobile tower solutions for civil and military ATC||19.11.2012|
R&S®VCS-4G in mobile tower solutions for civil and military ATC
|R&S®VCS-4G for shelter applications||19.11.2012|
R&S®VCS-4G for shelter applications
|R&S®VCS-4G for drilling companies/offshore industry||15.10.2012|
R&S®VCS-4G for drilling companies/offshore industry
|20 MHz Demodulation Bandwidth for Level Measurement||09.10.2012|
The R&S®EB500 offers level measurement of signals with 20 MHz bandwidth.
|RF signal monitoring in DVB-T2 multi-PLP networks||24.07.2012|
Signal monitoring has proven an effective technique when it comes to identifying and correcting quality problems in transmitted TV broadcast signals during broadcast operation. For a DVB‑T2 signal using multiple physical layer pipes (multi-PLP), a separate receiver is required to analyze each PLP. The R&S®DVMS digital TV monitoring systems are extremely flexible and can be configured to meet customer's needs – from sequential PLP monitoring systems with a single receiver to systems providing seamless, parallel multi-PLP analysis.
|Measuring small signals accurately||13.07.2012|
For measurement settings below 10 mV/div, oscilloscopes typically reduce the measurement bandwidth in order to keep the trace noise as low as possible. The R&S®RTO is different: It offers the full bandwidth even for the most sensitive settings, and an A/D converter with more than 7 effective bits (ENOB) digitizes the signal.
|Multiple communications monitoring using memory scan||13.07.2012|
Monitoring on up to 10 000 channels with different parameter settings
|Replication of real-world RF signals in the lab||13.07.2012|
Recording, converting and playing back real-world signals
|Precise quality analysis for DOCSIS upstream signals||13.07.2012|
DOCSIS has become the established standard for return channels when it comes to implementing interactive services in broadband cable networks. The quality of these signals is essential to network efficiency. The analysis can be done using the highprecision R&S®ETL, R&S®EFA and R&S®FSH3-TV TV test receivers that have proven themselves in the downstream. These T & M instruments can be quickly and easily configured for measuring the upstream.
|Using phase noise analysis to optimize the signal quality of DVB-T transmitters||13.07.2012|
DVB-T signal quality is determined by measuring the modulation error ratio (MER). However, a poor MER does not indicate its causes since different interference factors overlap at the transmitter when a signal is generated and transmitted. The R&S®ETL TV test receiver now has a unique new measurement capability that makes it possible to demonstrate to what extent the modulator's phase noise affects the MER.
|DVB-xx tests for set-top boxes||13.07.2012|
Wide range of set-top box tests in line with current DVB-xx standards using a variable, future-ready test system
|Dynamic Scenario Simulation with the R&S®SMU200A||12.07.2012|
|Digital dividend: testing of TV receiversDigital dividend: testing of TV receivers||20.06.2012|
The R&S®SFU broadcast test system is used as a reference signal generator to simulate the influence of LTE and other mobile radio signals on digital TV signals and receivers.
|Simplify software development for measurement applications||27.02.2012|
Remote control drivers accelerate application software development while meeting complex test and measurement requirements.
|RF Power Monitoring System||03.02.2012|
Failsafe RF power monitoring and control with up to 100 power sensors operating in parallel.
|Demodulation of four channels in parallel with just one receiver||24.11.2011|
Multichannel signal reception in parallel using digital downconverters in a monitoring receiver.
|R&S®VCS-4G VoIP for Air Traffic Control (ATC on its way to Voice over IP)||02.11.2011|
The ATC world is standing before a game changing development in voice communications infrastructure.
|Testing and monitoring DVB-T2 signal feed via new T2-MI interface||01.09.2011|
An error in DVB-T2 signal feed to the transmitter can cause failure of the entire DVB-T2 network. For this reason, the established ETSI TR 101 290 DVB measurement guidelines have been expanded to include measurements for the new T2-MI interface. The instruments of the R&S®DVMS family monitor T2-MI signals by performing these newly defined measurements and even provide in-depth analysis of these signals.
|Testing TV and audio broadcast receivers in cars||01.09.2011|
When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers guarantee the receiver functionality, this functionality must be tested when the receiver is integrated into the car.
|Automate testing of your infotainment systems||22.08.2011|
Assure the quality of your infotainment components during the development phase.
|Calibrate your weather radar receivers using the R&S®SMB100A||25.01.2011|
The R&S®SMB100A analog signal generator is the ideal calibration source for weather radar receivers due to its highly accurate output level.
|Radar-frontend-test - Phase-coherent multichannel signal simulation||21.01.2011|
|Use the LTE test case wizard for your eNB conformance testing||12.11.2010|
The test case wizard for signal generators simplifies LTE base station receiver and performance testing in line with 3GPP TS 36.141 Release 8 by providing complete and automatic configuration of the instrument.
|Verify your avionics navigation equipment||04.11.2010|
Rohde & Schwarz offers unique one-box solutions for reliable testing of air navigation systems such as ILS, VOR and DME.
|Test the ON/OFF power of your TD-LTE base station||23.08.2010|
The R&S®FSQ signal analyzer provides the high dynamic range needed to accurately measure the ON/OFF power of your transmitter in accordance with 3GPP TS 36.141.
|Easy testing of TV transmitters' out-of-band emissions||11.08.2010|
Automatic generation and use of transducer factors makes it possible to test out-of-band emissions with the R&S®ETH handheld TV analyzer, without an external bandstop filter.
|GPIB to LAN converter||02.08.2010|
Integration of instruments with an Ethernet interface, such as the R&S®OSP open switch and control platform, into a pure GPIB bus system.
|Troubleshooting utilizing SNMP||16.07.2010|
For solving intermittent faults in broadcast networks
|Visualize your radio network performance||07.07.2010|
The drive test solution from Rohde & Schwarz features convenient data export to visualize your radio network performance in Google Earth.
|Extensive audio testing of TV sets||01.07.2010|
Powerful solution featuring the R&S®DVSG digital video signal generator and the R&S®UPV audio analyzer.
|Simplify field testing of remote radio heads||16.06.2010|
In combination with the R&S®FSH handheld spectrum analyzer, the R&S®EX-IQ-Box digital signal interface module significantly simplifies RRH installation and inspection in distributed network architectures.
|R&S®MX400 Mobile Tower For ATC and air defense||27.05.2010|
The R&S®MX400 provides all ATC equipment needed for rapid, safe and reliable ATC operation. It is a completely self-contained system designed for quick installation and for long-term deployment under adverse weather conditions.
|Production testing of RF and communications modules||23.04.2010|
Modular, flexible and scalable – from pre-batch to mass production
|Test your multichannel FM car radios||15.04.2010|
Combining the new R&S®UPP audio analyzers with the R&S®SMB100A signal generators provides the most compact and fastest test solution for modern FM car radios
|Flexible measurement of luminance and chromaticity of TV displays||31.03.2010|
Compact solution including the R&S®DVSG digital video signal generator and the Konica Minolta CS200 chromameter/CS2000 spectroradiometer
|Test your remote radio head solutions||23.03.2010|
Signal generators and analyzers from Rohde & Schwarz are the ideal solution for testing your RRH not only at the RF, but - using the R&S®EX-IQ-Box - also via the digital I/Q interface
|Test the receiver performance of your WiMAX™ device||02.03.2010|
The most compact test solution with base station emulation and MIMO fading provides fully controlled network conditions for receiver performance testing of mobile terminals.
|Flexible broadcast network management||11.01.2010|
SNMP based broadcast network monitoring & control Software
The R&S®DDF-TRA option enables the R&S®DDF0xE/A digital direction finders to locate specific TETRA terminals and base stations when used together with a TETRA analyzer.
|Maximize WiMAX™ data throughput||12.11.2009|
Reaching the physical throughput limits with the R&S®CMW270 WiMAX™ communication tester
|Test the performance of your LTE eNB||29.10.2009|
Reliable testing of HARQ feedback and UL timing adjustment on LTE eNBs with the R&S®SMU200A simplifies eNB performance testing and eliminates the need for test UEs
|Phase-coherent multichannel signal simulation||25.09.2009|
Tester for phase-coherent measurements on radar frontends in development, production and service
|Optimize your HSPA+ design||29.07.2009|
Simultaneous DL throughput verification and UL transmission testing with the R&S®CMW500
|Speed up your femtocell production||18.06.2009|
Test and measurement solutions for designing and manufacturing femtocell devices
|Smooth your LTE signal||05.06.2009|
Time windowing and how OFDM impacts the shape of your LTE signal
|Shape your LTE signal||20.05.2009|
Filtering and how it impacts the performance of your LTE signal
|Mobile realtime I/Q streaming||09.01.2009|
Seamless detection with a bandwidth of up to 20 MHz
|Automatic BTS localization for 2G and 3G mobile radio networks||30.09.2008|
|T & M solutions for production||05.07.2007|
Automatic functional testing of roof antennas
|EMF long-term measurements||12.06.2007|
Automated long-term measurements expand snapshot measurements associated with risk communication
|Automatic monitoring of radio signals at airports interfering with radio services||04.09.2006|
|Automatic monitoring of operating parameters of radio transmitters from 100 kHz to 6 GHz||04.09.2006|
Monitoring solutions for operators of security radio networks for police, rescue services, ambulances, fire brigades and radio and TV broadcasting transmitters and other regional and national services.
|Automatic monitoring of emission parameters of registered broadcasting transmitters||04.09.2006|
|Automatic monitoring of radio signals interfering with sensitive devices in hospitals||04.09.2006|
|Combination test Expanded test method for optocouplers||17.07.2006|
|Function Test of Tire Pressure Monitoring Systems||10.05.2006|
|Combinational tests for telephone terminal equipment||26.04.2006|
|Brake and Safety Electronics (ABS, ASR, ESP)||30.03.2006|